info@meslo.com
+357 226 66 080
BWB BIO – AV Flame Photometer with printer and AFHS link
Complete with firmware for two separate calibration, curves, autocal when AFHS enabled Na, K and enhanced Li detection, Gas regilator, in-build air compressor, BIO-starter pack, “Just Add Gas”, (100V-250V, 50/60 Hz) Drain Trap Connecting Tubes Operation Manual PC Software (with interface cable), Fluid Kit Serum Calibration Standards (5 x 25ml Points 1,2,3,4,6 and 1 x 500ml Point 5- Calibration Correction), Urine Calibration Standards (5 x 25ml Points 1,2,3and 4 and 1 x 500ml Point 5- Calibration Correction), Diluent Concentrate (500ml), Decon 90 (150ml), Labware Kit 1ml Pipettes(10), 10ml Pipettes (10) , 100ml Volumetric Flask (1) and Sample Cups (100), IQ, OQ, PQ included, User selectable Li Internal Reference, Left handed Format
-
Specially configured for a range of user interests
-
“IRS” (Internal Reference Standard) caesium or lithium option
-
Single point calibration correction
-
Internal reference standards
-
10K ppm calibration standards for each element
-
Analysing Li along with Na and K
-
Operator independent determination of results
-
Advanced automated determination of results
-
Integrated printer with environmentally friendly ink
-
IQ, OQ, PQ web-based certification standard on BIO AV and available on all BWB FES units
Available on backorder
Sample rate
2 – 3.5ml/min
Tubing materials
Silicone and Tygon®
Required desk space for Instrument
50cm (H) x 45cm (W) x 45cm (D)
For Safety reasons the Flame photometer requires1m of unobstructed space above to allow dissipation of heat from the chimney.
Instrument size
BIO AV Flame Photometer
51cm (H) x 39cm (W) x 35cm (D)
(20in x 15in x 14in)
Shipping
65cm (H) x 49cm (W) x 43cm (D)
(25in x 19in x 17in)
Weight
BIO AV Flame Photometer 14kg (30.8lbs)
Shipping 25kg (55.1lbs)
Specificity
Na/K/Li = <1% to each other when
equal in concentration at <100ppm
Optimal range
Multi-point calibration
Na – 0.0043 – 300mmol/l*
K – 0.0013 – 200mmol/*
Li – 0.0072 – 20mmol/l*
*With required Dilution Ratios
Reproducibility
<1% Coefficient of variability for 20 consecutive samples over ten minutes at concentrations of 100ppm equivalent or less. (After instrument stabilisation).
Limit of detection (LOD) and limit of quantification (LOQ)
LOD LOQ
Na – 0.0013mmol/l Na – 0.0043mmol/l
K – 0.0005mmol/l K – 0.0013mmol/l
Li – 0.003mmol/l Li – 0.0072mmol/l
Time to stability
Less than 15 seconds after sample
is introduced into the flame
Ions measured
Na, K, and Li
Recommended minimum warm up
time based on ambient temperature
21°C – 25 minutes
Power requirements
100V – 250V AC at 50 or 60Hz
Fuel requirement
Propane, Butane or Natural Gas* regulated to 19Bar. Flow rate of 0.4l/min
*with modifications. BWB Technologies recommends either Propane or Butane for optimum results.
Readout
LCD, four line, alpha numeric, back lit.
| Parameter | Value |
|---|---|
| Product type | Multi Channel Flame Photometers |
| Brand | BWB Technologies |
